Clay-paky POINT MH User Manual download pdf

1. SELECT

Not in menu:

Allows for transition between: DMX address setting, Menu access, Waiting status

(display of DMX address or operating mode symbol).

In a menu:

Allows you to exit functions without making changes or to go back to the

programming menu.

2. UP/DOWN

Increases or decreases the DMX address.

Selects the next or previous function in the menus.

3. ENTER Confirming button.

4. SEL

(red led) When on it indicates that you are in the setting phase (DMX address or menu).

5. TX

(yellow led) When on it indicates that the projector is in MASTER mode and can control other MH Points

6. DMX

(green led) When flashing in DMX mode:

in DMX mode: it indicates that no DMX input signal is present or that an address setting is invalid.

When flashing in SOUND TO LIGHT mode: indicates sound signal peaks.

When on it indicates that a DMX input signal is present

7. Display

Shows the selected functions.

INSTRUCTIONS MANUAL

12V 50W

POINT MH

CONTROL PANEL

OPERATION

The projector may be programmed to operate in AUTOMATIC mode (it carries out previously set scenes or sequences), or controlled by a CONTROL UNIT.

7654

OPERATION WITH CONTROL UNIT

All the projectors must be in SLAVE mode (SLA);

the projector receives a DMX signal and carries out the controls transmitted from the

control unit.

2) SA

(STAND-ALONE Mode): The projector operates individually.

In this mode, the “

Snd” SOUND TO LIGHT option (movement by Audio signals) may

be set.

3) SAt

(MASTER Mode): The projector generates a DMX output signal that can pilot

other projectors in

SLAVE mode (SLA).

In this mode, the “Snd” SOUND TO LIGHT option (movement by Audio signals) may

be set.

Address: 1

Slave

Max

100

Mode

Master (SAt)

Address: 1

Slave

Address: 1

Slave

DMX

mode (SLA) mode (SLA) mode (SLA)

Mode

Stand-Alone (SA)

Address: 1

Mode

Slave (SLA)

Max

100

Mode

Master (SAt)

Address: 1

Mode

Slave (SLA)

Address: 1

Mode

Slave (SLA)

DMX

Address: 1

Mode

Slave (SLA)

Control unit

Address: 5

Mode

Slave (SLA)

Address: 9

Mode

Slave (SLA)

DMX

Set the DMX digital signal address on each projector: addresses are valid from 1 to 507

(see Programming Operation with Control Unit).

Each projector uses 4 to 6 control channels, depending on whether the Pan Fine / Tilt

Fine high resolution

Hlr function (for greater movement precision) is active..

CHANNEL FUNCTION

COLOUR DISC

DIMMER

PAN (horizontal movement)

TILT (vertical movement)

CHANNEL FUNCTION

COLOUR DISC

DIMMER

PAN (horizontal movement)

PAN FINE

TILT (vertical movement)

TILT FINE

Channel functions and options

with option Hlr OFF (the projector uses 4 channels)

Example of address setting:

Projector 1

➞

Address 1

Projector 2

➞

Address 5

Projector 3

➞

Address 9

.....................

➞

......................

Example of address setting:

Projector 1

➞

Address 1

Projector 2

➞

Address 7

Projector 3

➞

Address 13

.....................

➞

......................

with option Hlr ON (the projector uses 6 channels)

AUTOMATIC MODE

In automatic, the projector may be configured in three different modes: SLA - SA - SAt

SLA

(SLAVE Mode): The projector receives a DMX signal and carries out the

sequences transmitted from a main projector in

MASTER mode (SAt).

The projector must have address 1 (see Programming Automatic Mode: SLAVE

mode “SLA”).

1 2 3 4

Summary of Contents

Page 1 - POINT MH

1. SELECTNot in menu:Allows for transition between: DMX address setting, Menu access, Waiting status(display of DMX address or operating mode symbol).

Page 2 - PROGRAMMING

WARNINGCaution: The display returns to its initial visualisation after60 sixty seconds of inactivity. The current program, not yetconfirmed with ENTER

Page 3 - DISPLAY OFF

S EENTERSELECTLIPress UP/DOWN toselect tIL function.Press ENTER to accessthe function.S EENTERSELECTL0The display shows theminimum position (LO)for Ti

Page 4 - SETTING RESETS

TEST MENU S EENTERSELECTPOPress SELECT twice.The red led lights up andthe display shows: OPt.S EENTERSELECTCFPress ENTER to accessFC function.S EENTER