Clay-paky ATLAS (HMI 575) User Manual download pdf

Alimentazione

ATLAS

ENGLISH

• Unpacking

Open the cardboard box, remove the projector from the packing and position it on a

horizontal support surface. Remove the components contained in the bags inside the

packing.

Identify the light bulb change label (1) on the appliance and, if necessary, replace it

with one of the optional multi-language labels.

Ensure that this label is never removed since it contains important safety infor-

mation.

IMPORTANT: Carefully read all parts of the instruction manual. Knowledge of

the information and prescriptions contained in this document is essential for

correct, safe use of the appliance.

PROJECTOR INSTALLATION

POWER SUPPLY AND SET-UP

The projector is set up to operate at the power supply voltage and frequency shown

on the electrical data label (5) on the back of the projector itself. Ensure that these

values correspond to the electricity mains network voltage and frequency.

IMPORTANT: connection to a power supply system with efficient grounding is

mandatory (Class I appliance).

• Control signal connection

• Mains power connection

The operations described in this heading must be carried out by a licensed elec-

trician.

The projector must be connected to the electricity mains network using the spe-

cial socket provided. It is recommended that each projector is connected through

its own switch, so that it can be individually switched on and off remotely.

0 - 10V 0 - 10V 0 - 10V

0 - 10V

- Simultaneous and equal projector operation

- Independent projector operation

0-10V CONNECTION

The connection between projector and control unit and between several projectors

must be made with a shielded two-pole cable with Cannon 5 PIN XLR plug and sock-

et at the ends.

STOP

INSTRUCTION MANUAL

• Projector support preparation

Fix bracket (2) with the special screws (3) and lock it by tightening handles (4).

• Fitting the light bulb

Refer to the instructions for changing the light bulb in paragraph 5 MAINTENANCE.

• Projector installation

The projector can be fixed in any position, with its operating characteristics remain-

ing unchanged.

IMPORTANT: Fix the projector in the required position using the special holes

in bracket (2).

The use of two 12 mm ø screws complete with nuts and spring washers is

recommended.

Ensure the stability of the fixing point before positioning the projector.

• Minimum distance of the lighted objects

The projector must be positioned so that the objects

struck by the light beam are at a distance of at least

0.5 m (1’ 8”) from the lens of the projector itself.

• Minimum prescribed distance of flammable materials from every point of the

body of the appliance: 0.07 m (3”).

Assembly of the appliance on normally flammable surfaces is permissible.

IMPORTANT: For better and more reliable operation of the appliance, the ambi-

ent temperature must not exceed 35° C (95° F). Protection level IP 20: the appli-

ance is protected against penetration of solid bodies with a diameter of more than

12 mm (0.5”) (first figure 2), while it is not proof against drips, rain, sprays and jets

of water (second figure 0).

HMI 575

Mains

ENGLISH

(

1’ 8”

)

0.5 m

HMI 575

1 2 3

Summary of Contents

Page 1 - INSTRUCTION MANUAL

5AlimentazioneLNATLASENGLISH• UnpackingOpen the cardboard box, remove the projector from the packing and position it on ahorizontal support surface. R

Page 2 - MAINTENANCE

6CHANNEL FUNCTION3• STOP/STROBE - channel 1With the cursor at 0% all bands areobscured. In the cursor intervalbetween 0% and 25% the bands areprogress

Page 3 - WIRING DIAGRAM

7250 V10AT5 x 20FUSEPOSSIBLE REASONSCHECKS & REMEDIESTROUBLESHOOTING6No mains power supply. Check that power is reaching thesupply socket and/o