1ALPHA BEAM 700C61360®INSTRUCTION MANUALCongratulations on choosing a Clay Paky product! We thank you for your custom. Please note that this product,
Save ToPreset 310ALPHA BEAM 700SHUTTERShutter on errorUsed for automatically closing the stop/strobe in the event of Pan/Tiltposition error.1)PressF-
11ALPHA BEAM 700SYSTEM ERRORSShows a list of warnings and messages relevant to errors occurred sincethe fixtures switching-on.1) Pressing Fyou are all
2) Press Fto reset partial lamp strikes hours, a confirmation message(Are you sure ?) appears on the display.3) Select YES to reset partial counter or
13ALPHA BEAM 700To enable the "Advanced Menu" set up the "Access code" (1234) using theUP B, DOWN C, RIGHT Ekeys.PressF- "Men
14ALPHA BEAM 700Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section.Opening the head cov
15ALPHA BEAM 700Continue ➔Lower SideUpper Side 2Lower SideAUpper Side1A3A131412 12Lamp change - Fig 13Take the new lamp out of its package and
16ALPHA BEAM 70012084702/001085601/001085909/001085603/001085801/001085910/001085802/001085606/001Upper Side15Replacing fixed gobos (ø 31.5 mm – max 2
17ALPHA BEAM 700Upper Side21085523/001 085506/001085528/001085527/001085526/001085525/001085524/00112 17Replacing rotating gobos (ø 25.7 mm - max 23 m
18ALPHA BEAM 700Periodical cleaning- Fig. 19To ensure optimal operation and performance for a long time it is essential to periodically clean the part
19ALPHA BEAM 700Lower Side243Upper Side1thermostat20Extraction of the effect modules: Preliminary operations - Fig. 20Continue ➔
2ALPHA BEAM 700• InstallationMake sure all parts for fixing the projector are in a good state of repair.Make sure the point of anchorage is stable bef
20ALPHA BEAM 700Extraction of the effect modules - Fig. 21IMPORTANT: Grasp the modules using the support structure and not the details which could get
21ALPHA BEAM 700405(15.94")385(15.16")390(15.35")220(8.66")635(25.00")435(17,13")505(19,88")520(20,47")Power s
22ALPHA BEAM 700ALPHA BEAM 700CHANNEL FUNCTIONCHANNELSTANDARD VECTORCHANNEL MODECYAN MAGENTA YELLOW COLOUR WHEELSTOP / STROBEDIMMERDIMMER FINEIRISSTAT
ALPHA BEAM 700BIT % EFFECT255 100COLOUR EXCLUDED0 0.0COLOUR INSERTEDCHANNEL 1CYANCHANNEL 2MAGENTACHANNEL 3YELLOWBIT%EFFECT255 100COLOUR INSERTED0 0.0C
24ALPHA BEAM 700• PRISM ROTATION - channel 13STOPFAST ROTATION (120 rpm)SLOW ROTATION (3 rph)SLOW ROTATION (3 rph)FAST ROTATION (120 rpm)BIT % EFFECT1
25ALPHA BEAM 700• FROST - channel 14• FOCUS - channel 15BIT % EFFECT255 100DISTANT0 0.0NEARBIT % EFFECT255 100FROST INSERTED0 0.0FROST EXCLUDED• PAN F
26ALPHA BEAM 700•LAMP CONTROL (only with option LAMP DMX On) - channel: 22IMPORTANT: Alpha Beam 700 is not provided with hot restrike igniterLAMP ON (
27ALPHA BEAM 700Timing Channel Channel function 23 Pan - Tilt time
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035 -654311 - Fax +39-035-301876 - www.claypaky.itRev. 2 02/11 Cod. 09910
UNLOCKEDLOCKED45°45°45°45°45°45°45°45°45°45°45°45°45°3ALPHA BEAM 700UNPACKING AND PREPARATIONLamp 700W(fitted into projector)0991012 x 183102/802190°9
4ALPHA BEAM 7004123215INSTALLATION AND START-UPConnecting and disconnecting power cable - Fig. 5Installing the projector - Fig. 4The projector can be
5ALPHA BEAM 700Switching on the projector - Fig. 8Press the switch. The projector starts resetting the effects. At the same time, the following inform
ALPHA BEAM 70062828Reversal of the display - Fig. 9To activate this function, press UP Band DOWN Ckeys simultaneously while the display is in the rest
7ALPHA BEAM 700System ErrorsInformationFixture HoursLampHours4LampManualControlResetChannel6MAIN MENUMENU SETTINGSet UpOptionInformationManualControlT
8ALPHA BEAM 700DMX ADDRESSNOTE: without the DMX signal the Address (XXX) flashingAllows you to select the DMX ADDRESS.1) Press F- the current DMX Adre
9ALPHA BEAM 700 LAMP DMXUsed for enabling lamp remote control channel.1) Press F- the current settings appear on the display (On or Off).2) Use the U
Comments to this Manuals