Clay-paky SHADOW User Manual download pdf (Page 7)

• Minimum distance of inflammable materials from any part of the fixture:

0.10 m (4”) for QS and HMI 1200 Basic versions, 0.07 m (3”) for HMI 575 Basic version.

The fixture may be mounted on surfaces rated normally inflammable.

IMPORTANT: For better and more reliable operation of the projector, the ambient

temperature must not exceed 35° C (95° F). Protection factor IP 20: the fixture is pro-

tected against penetration of solid bodies more than 12 mm (0.5”) in diameter (first

digit 2), but can be damaged by spray, jet, drip or rain water (second digit 0).

ENGLISH

SHADOW

POWER SUPPLY AND INTERFACE

• Connecting to the electrical power supply

The operations described in this heading must be carried out by a licensed

electrician.

It is good policy to connect projectors to the power supply by way of dedicated

switches, so that each can be turned on and off individually from a remote station.

INSTALLING THE PROJECTOR- SAFETY INFORMATION

IMPORTANT: Read carefully. It is essential for the correct and safe use of

he equipment that erectors and operators should be fully conversant with

he information and instructions given in this manual.

INSTRUCTION MANUAL

•

Unpacking

Open the wooden box, remove the projector from the packing and place it on a flat

orizontal surface. Unpack the standard accessories supplied with the equipment.

nspect the lamp change label (1) on the projector cover and replace it with one of the

optional language versions if necessary.

Make certain that the label is never removed, as it displays important safety

nformation.

• Initial assembly operations

Position the bracket (2) on the graduated plate (3) at the desired height, select the

required hole and insert the bushing (4), the chamfered washer (5) and the screw (6)

and tighten the assembly using the supplied Allen wrench.

The bracket can also be mounted on the top of the projector for truss mounting by

inverting the position of the graduated plate (3).

Position the support as desired and then secure it by tightening the knobs (7).

• Fitting the lamp

Refer to directions for replacement of the lamp given under heading 8 MAINTE-

NANCE.

• Installing the projector

The projector can be mounted in any position without its operating characteristics

being affected.

IMPORTANT: for ceiling installation secure the projector in the desired position by

means of the holes in the support. Secure preferably using two ø12 mm bolts with

nuts and lock washers.

Make certain that the anchorage is stable before positioning the projector.

• Minimum distance from target objects

The projector must be positioned in such a way

that objects struck by the beam are separated from

the fixture by at least the distance specified on the

lamp change sticker next to the symbol shown in

the figure on the right.

The projector is designed to operate at the voltage and frequency indicated on the

electrical data plate (8) affixed to the rear end.

Check that these two values correspond to the mains voltage and frequency.

IMPORTANT: the projector must be connected to a power supply circuit having

a proper earth system (Class I appliance).

Mains

0 - 10V 0 - 10V 0 - 10V

• Connecting the control signals

SHADOW BASIC followspots can be controlled only from the integrated control panel,

while SHADOW QS models can also be controlled from a remote external controller.

0-10V CONNECTION

When both the external 0-10V controller and the integrated control panel are con-

nected, the higher level signal assumes priority.

ENGLISH

S-ST HMI 1200

S-LT HMI 1200

Basic HMI 1200

Basic HMI 575

(5’ 11”)

1.8 m

HMI 575

(8’ 2”)

2.5 m

HMI 1200

•

Photobiological Safety

CAUTION. Possibly hazardous optical radiation emitted from this

roduct. Do not stare at operating lamp. May be harmful to the eyes.

he fixture must be positioned so that the minimum distance between

the front lens and human eye is at least 2 metres to prevent personal

photobiological risks.

This product is intended for the following areas of application:

tudios, stages, theaters, exhibitions, trade fairs, events, theme

arks, entertainment venues, architectural lighting and similar

Not suitable for household illumination

Not for residential use

Disposing

This product is supplied in compliance with European Directive

2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To

reserve the environment please dispose/recycle this product at the

nd of its life according to the local regulation.

Gruppo di

rischio 2

econdo la norma

N 62471

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

Clay-paky SHADOW User Manual Page 7

Comments to this Manuals

Related products and manuals for Lighting Clay-paky SHADOW