Clay-paky ASTRORAGGI POWER User Manual download pdf (Page 2)

• Replacing fuses

To replace the fuses, press the tab (9) and

pull out the fuse holder (10).

Replace any blown fuse with one of the same

type and rating as indicated on the label (11)

attached to the holder (10).

Insert the fuse holder and push in to engage

the tab (9).

• Routine cleaning

To maintain the light output of the projector

undiminished, parts that tend to accumulate

dust and grease must be cleaned periodically.

In most circumstances, the projector will give

long and trouble-free service if these simple

guidelines are followed.

To remove dirt from the lenses and filters, use

a soft cloth moistened with any liquid detergent

suitable for cleaning glass.

IMPORTANT: do not use solvents or alcohol

Parts that need cleaning frequently.

Internal components should be cleaned once a

year by dislodging dust and dirt with a brush

and removing it simultaneously with a vacuum

cleaner.

IMPORTANT: isolate the projector from the electrical power supply before commenc-

ing maintenance work of any description. The maximum temperature on the outer sur-

face of the projector under normal operating conditions is 120°C (248° F).

After switching off, do not remove any part of the projector for at least 5 minutes, as

indicated on the lamp change label (1). Once this time has elapsed, the risk of a lamp

exploding is practically zero. If the lamp needs changing, wait a further 15 minutes to

avoid the risk of burns.

In the event of a lamp exploding, the appliance is

designed to prevent fragments of glass from being

scattered. The lenses supplied with the appli-

ance must be fitted at all times, and if visibly

damaged, must be replaced with genuine

spares.

•

Projector address codes (for digital signals)

Each ASTRORAGGI POWER projector uses 2 control channels. To ensure that differ-

ent projectors are addressed correctly by the controller, a code must be assigned to

each one. This operation is carried out on each ASTRORAGGI POWER by setting the

microswitches as indicated in the table below.

Setting the TEST switch to the ON position for a few seconds with the projector pow-

ered-up, an auto-reset routine is carried out. Leaving the TEST switch at the ON posi-

tion for a longer period, a full self-test program will be completed; once the operation

has terminated, return the switch to the OFF position.

TEST

256

128

10987654321

STOP

ROTATION

DMX 512

RS232/423

PINS : 1 = ,2 = SIG - ,3 = SIG +

PINS : 1 = ,2 = SIG ,3 = SIG

DIGITAL INPUT

Projector 1-2

3-4

OFF

TEST

256

128

OFF

5-6

4 7-8

5 9-10

6 11-12

7 13-14

8 15-16

9 17-18

10 19-20

CODIFICA

- Channels

Projector - Channels

ANALOGUE INPUT

ATRORAGGI

POWER

1 = ROTATION

2 = STOP

0-10V

OFF

Spotlight selection

CHANNEL FUNCTIONS

CHANNEL

FUNCTION

DOME ROTATION

DIMMER/STOPPER/STROBE

From 0% to 49.7% the internal

dome turns anti-clockwise through

360°. When the slider reaches

50% the dome starts spinning at

maximum speed and then it grad-

ually slows down until it comes to

a stop on 74%. At 76% the dome

starts turning in the opposite

direction starting from minimum

speed and gradually accelerating

up to maximum speed when the

slider is on the 100% position.

• DOME ROTATION - channel 1

100%

50%

49.7%

76%

74%

• DIMMER/STOPPER/STROBE - channel 2

In the 0% to 50% range of adjustment,

the dimmer opens gradually to maxi-

mum aperture. Strobe effect is pro-

duced from 54.7% to 95%, with fre-

quency increasing from 1 flash/4 sec-

onds to 2 flashes/second. The aper-

ture remains fixed between 95% and

100% of the range.

•

Changing the lamp

Unscrew knob (6) and open cover (7)to

access the lampholder. Remove the

lamp (8) from its fitting by gripping it at

the base and pulling it upwards. Locate

the new lamp in the fitting and ensure

that the pins are positioned correctly.

MAINTENANCE

ASTRORAGGI

POWER

CAUTION: The projector uses a high pressure discharge lamp with

external starter.

- When fitting a new lamp, read the manufacturer’s instructions carefully.

- The lamp must always be changed without delay if damaged or deformed by heat.

CODE

250 V

10A T

5 x 20

FUSE

11 9

1 2 3

Comments to this Manuals

No comments

Clay-paky ASTRORAGGI POWER User Manual Page 2

Comments to this Manuals

Related products and manuals for Projectors Clay-paky ASTRORAGGI POWER